Whole-home duct cleaning
Dryer vent cleaning
Camera inspection
Sanitizing & deodorizingWhole-system duct and dryer vent check with before-and-after photos - you see exactly what came out of your vents
That "$99 whole-house special" is a bait ad - the real number appears once they are in your hallway, or the "clean" is a shop-vac at the register. We photograph the inside of your ducts before and after instead.
Why West Seattle Homeowners Choose Lennox Air Duct Cleaning
Air Duct Cleaning West Seattle provides independent Lennox air duct cleaning, coil cleaning, and duct sealing for West Seattle homeowners. Lennox systems have specific behaviors – variable-speed blowers that pull hard on return ducts, CBA and CBX air handler cabinets with foil-faced duct-board transitions that sag over time, and horizontal attic air handlers with cabinet panels that come loose – and we clean around how your system is actually installed, not just the box Lennox shipped. We’re not affiliated with Lennox, and we’re not authorized by them. We’re an independent local service working on their equipment every week.
That independence matters in West Seattle. The canopy of cedar and alder here, plus the damp air, pushes pollen and fine debris into return ducts in ways a sunnier, less wooded part of the region never sees. Many homes mix early-1900s galvanized trunks with later flex runs, so we clean by section, not by blast. Call (877) 492-4032. We answer 24/7. Fast dispatch from 7am to 7pm, Sunday through Friday.
Why Trust Air Duct Cleaning West Seattle for Your Lennox Air Duct Cleaning?
Our technicians have up to 8 years of experience, and most of that time has been spent inside residential cabinets and crawlspaces where Lennox systems actually live. We know the airflow path through the Merit series, the Elite series, and the Dave Lennox Signature Collection from forced-air intake to supply trunk. The point isn’t to sell you equipment. The point is to read the installation.
We work with quality parts that fit Lennox equipment. OEM Lennox filter racks, cabinet gaskets, and coil support parts get spec’d when they’re the correct fit and they perform. Quality aftermarket flex duct, mastic, and foil tape get used where the OEM part adds cost without a performance gain. That’s how a Lennox cabinet stays sealed without inflating the bill.
Warranty-safe service means we don’t cut into structures we don’t need to cut, we don’t modify airflow paths in ways that change how the system was commissioned, and we document what we find. When a Lennox part does need replacement, we tell you that in writing, with the option to go OEM or to hold the line on cost. From intake to output, one crew handles every step.
Styles & brands we work with
- Whole-home duct cleaning
- Dryer vent cleaning
- Camera inspection
- Sanitizing & deodorizing
Common Lennox Air Duct Cleaning Problems We Fix in West Seattle
Lennox equipment behaves in predictable ways when the surrounding duct system isn’t maintaining its end of the bargain. These are the recurring problems we find in West Seattle homes.
- Variable-speed ECM blowers pulling on an undersized return. Lennox Signature and Elite furnaces with variable-speed ECM blowers move a lot of air at higher demand. When the return duct is undersized or leaking, that pull doesn’t get satisfied at the grille – it draws dust straight through cabinet joints and into the coil area instead of through the filter. You see it as a dirty coil and a gritty film on the blower wheel. The fix starts at the return, not the blower.
- Failing foil-faced duct-board transitions at the plenum. Lennox CBA and CBX air handlers are frequently connected to the supply plenum through thin foil-faced duct board. That material sags and tears as it ages, and once it tears, fiberglass fibers work their way into the supply trunk. Every register in the house gets a share of them. Replacing the failing section with sealed metal or insulated flex stops the source.
- Damp dust film from two-stage and modulating operation. A Lennox EL296V or SL280V runs long stretches at low fire. That’s efficient, but it also means the evaporator coil and blower wheel sit in a slow, moist airstream for hours. In West Seattle’s cool, wet winters, a fine damp dust film builds up faster on these systems than on a single-stage furnace that cycles hard and dries out between runs. Coil cleaning isn’t optional maintenance on these units – it’s the baseline.
- Loose cabinet panels and unsealed knockouts on attic air handlers. Horizontal Lennox air handlers in West Seattle attic installs often show cabinet screws that have walked loose and punch-outs at the cabinet that were never sealed. Both draw attic air and insulation fibers into the return. The coil gets coated, the filter loads early, and the system runs dirtier than it should. Mastic and a fresh set of cabinet gaskets close those gaps.
- Pollen and cedar duff loading the filter slot in spring. Cedar and alder pollen from the hills coat outdoor condensers and get drawn into return ducts. Homes near Schmitz Park and Camp Long often show a fine green-yellow film in the filter slot by mid-spring. It’s not a filter failure – it’s a seasonal load that accumulates inside the return trunk before the filter catches it.
Lennox Parts & Our Repair-vs-Replace Approach
Choosing parts for a Lennox system is a fit question first. A filter rack built for a Lennox cabinet seals tighter than a universal one, and a coil support matched to the cabinet keeps the coil from walking. Those are the cases where OEM is the right answer. Flex duct, mastic, and foil tape are different – once they’re sealed and rated for the application, the OEM label adds cost without adding performance. We buy what works, not what carries a logo.
Repair vs. replace depends on structure. A dirty Lennox duct system, a sagging duct-board transition, a leaking cabinet joint – all of those are repair work, and replacing the air handler over a dirty duct is the wrong answer. Replacement becomes worth discussing only when the heat exchanger or the coil has failed outright, or when a coil has corroded through. A musty smell at startup is not a replacement signal. It’s a coil-and-cabinet-cleaning signal.
One flat price per system, agreed before work starts. Call (877) 492-4032 for a free estimate.
Our Lennox Service Process – Step by Step
- 1
Video inspection. We run a camera through the return trunk, the supply trunk, and the plenum connection to see how the Lennox cabinet and coil are actually feeding. A sagging duct-board transition or a torn cabinet gasket shows up immediately.
- 2
Diagnosis. We identify which Lennox problem is driving the symptom. Is the variable-speed blower starving for return air? Is the coil coated with damp dust? Is the filter slot bypassing?
- 3
Cleaning and repair. Rotobrush rotary brush extraction works the supply and return runs. Nikro HEPA-filtered vacuum holds particulate while we cut. If a duct-board transition needs replacement, we cut it out and seal the new section with metal or insulated flex.
- 4
Cabinet sealing. Mastic at the plenum, fresh gaskets at the cabinet joints, sealed knockouts. From intake to output, the cabinet holds.
- 5
Test and document. We verify airflow at the registers, run the Lennox furnace through a heat cycle, and document what we cleaned with before-and-after photos of your ducts.
See the difference
Before
After
Before
After
Before
AfterLennox Products We Service & Install in West Seattle
We service the full Lennox residential lineup – Merit series for the entry-level and replacement market, Elite series where the efficiency gains matter, and Dave Lennox Signature Collection where the homeowner wants the top of the residential range. That covers Lennox furnaces, air handlers including the CBA and CBX, and complete Lennox heating and cooling systems. We also handle air quality hardware from Honeywell and Aprilaire when the job calls for it, and Abatement Technologies equipment for elevated contamination scenarios.
Across all of it, we work with professional-tier extraction gear: Rotobrush and Nikro. Cleaner air starts with the right tools.
We Also Service These Brands
Lennox isn’t the only brand we know inside out. We work on Trane and Carrier equipment with the same process – video inspection, diagnosis, cleaning, and sealing. If you’ve got mixed brands under one roof, or you’re moving between brands on a replacement, the crew that shows up won’t need a second opinion.
FAQs – Lennox Air Duct Cleaning Service in West Seattle
No. Air Duct Cleaning West Seattle is an independent Lennox service provider, not affiliated with, authorized by, or endorsed by Lennox. We work on Lennox equipment because we know it, not because we carry their badge. If you need a factory-authorized service, that’s a different call, and we’ll say so up front.
Yes. We spec OEM Lennox filter racks, cabinet gaskets, and coil support parts when they’re the correct fit and they perform. Where a quality aftermarket part (flex duct, mastic, foil tape) does the same job without adding cost, we use it. What we won’t do is swap in a part that doesn’t fit the cabinet and then tell you it’s fine.
Most Lennox air duct cleaning visits run several hours, depending on the size of the system and how many runs need work. Full System Cleaning with coil cleaning and Duct Sealing takes longer than a supply-and-return clean alone. If a CBA or CBX duct-board transition needs replacement, add time for cutting and sealing that section. We scope it in the written estimate before we start.
We cover Lennox furnaces, air handlers including the CBA and CBX, and the duct systems and cabinets connected to them. That includes the Merit, Elite, and Dave Lennox Signature Collection lines. Call (877) 492-4032 if you’re not sure which Lennox system you have – we can walk through it with you.
Standard duct cleaning on your Lennox Merit system does not void the manufacturer’s warranty. What can affect warranty coverage is a service that changes the components it touches – cut cabinet panels, an altered plenum so the manufacturer’s airflow specs no longer match, or a coil pulled and reinstalled without proper gasketing. We work warranty-safe: we open the cabinet where the job needs it, seal it back the way it was built, and document the work. Call (877) 492-4032 if you want to talk about what a warranty-safe cleaning looks like for your specific system.
A dirty Lennox evaporator coil needs cleaning. A failed one needs replacement. The way to tell them apart is the camera – we look at the coil surface, the fins, and the coil support before we recommend anything. A coil that’s coated with the fine damp dust film that two-stage Lennox furnaces build up is a cleaning. A coil that’s corroded through or has physically failed is a different conversation. If you noticed dust on the return grille and a musty smell at startup on a Lennox Elite or Signature furnace paired with a CBA air handler in a West Seattle split-level, that’s usually a sagging duct-board transition plus an unsealed cabinet knockout pulling attic or crawlspace air past a loaded filter. Cleaning, sealing, and replacing the transition are the fix. Call (877) 492-4032 for an exact quote – estimates are free.
Yes. One crew handles the Lennox furnace, the air handler, the supply and return ducts, and any sealing or repair work in the same visit. That’s the point of doing it together – a furnace cleaned without a sealed cabinet and a cleaned return duct feeds its coil from the attic, and the coil is dirty again inside a heating season. One flat price per system, agreed before work starts. Call (877) 492-4032 to book it.
Because they’re not covering the same scope. A low-bid quote is usually a supply-side wipe with a shop vac and a hose, no camera, no coil cleaning, no cabinet sealing, and no Duct Repair & Sealing when a transition or a joint fails – which means the duct itself is still leaking air into your attic after the crew leaves. Our quotes are whole-system, and the written estimate sets the final price. Pre-purchase, we’ll show you exactly what’s in scope.
Typical estimates for Lennox air duct cleaning, evaporator coil cleaning, and related sealing work in West Seattle typically fall in the range of $450 to $1,400 depending on system size and how much duct repair the cabinet and plenum need. The written estimate sets the final price – no per-vent pricing, and you see before-and-after photos of your own ducts before we leave. Call (877) 492-4032 for an exact quote – estimates are free.
Book Your Lennox Service in West Seattle, WA
Whether you need Full System Cleaning on a Lennox Merit system, Evaporator Coil Cleaning on an Elite or Signature furnace, or Duct Sealing where a foil-faced duct-board transition has given way, we handle it in one visit with professional-grade equipment. One flat price per system, agreed before work starts. Before-and-after photos of your own ducts. Call (877) 492-4032 for a free estimate. We answer 24/7. Fast dispatch from 7am to 7pm, Sunday through Friday.
Written by the team at Air Duct Cleaning West Seattle.